2023 Landoll 9600 Series Field Cultivator 9630-20

Information

2023 Landoll 9600 Series Field Cultivator 9630-20

The New Era in Field Cultivators

The Landoll 9630/9650 Series Field Cultivator started with the need for efficiency. High residue levels, larger acreages, higher horsepower tractors and an ever-shrinking window of planting opportunities, the design team at Landoll had set the bar high. Customer feedback from today’s top producers was used to eliminate the shortfalls found in competitive units. All aspects of ultimate seedbed preparation were taken into consideration in the new design of the 9600 Series Field Cultivator.

It Starts with the Frame

High capacity tillage tools need to have a solid foundation to build from. The Landoll 9630/9650 Series Field Cultivator uses precision, laser-cut structural steel frame members that are robotically welded for ultimate strength and reliability. This process of manufacturing provides the end-user with peace of mind that the Landoll 9600 Series Field Cultivator will be reliable day after day and season after season. The deep frame allows for a “split the middle” shank arrangement for unrestricted residue flow for perfect seedbed preparation. The frame is the anchor for the self-leveling hitch and walking tandem transport axles. The shanks are attached to 4” x 3” structural steel tubes that offer true 6” shank spacing on all models.

There’s More

UHMW polymer is used on all rock shaft bearing surfaces. This provides for maintenance-free operation in this high wear area. The lift circuit uses 10” stroke phasing cylinders throughout for even raise/lower cycles. The cylinders use hardened bushings in all pivots and nickel and chrome-plated rods for extended life. Single point depth control at the front of the machine provides precise depth control in ¼” increments. Pivoting wing gauge wheels are standard on the 28 through 50-foot models. 1 ¼” hinge pins on the wing fold operate on UHMW maintenance-free bushings.

Features may include:
  • Laser Cut, Robotically Welded Frame
  • 135” Frame Depth
  • 30” Minimum Between Shank Ranks
  • Self-Leveling Hitch
  • Cast Single Lip Hitch Cat. III or Cat. IV (Model Dependent)
  • Outrigger Gauge Wheels on 28’ – 50’ Models
  • Shanks with 190 lbs. Point Load (Spring Clamp or Two Piece S-Tine)
  • 26 ½” Under Frame Clearance
  • 6” Shank Spacing
  • 8” Sweeps, 47 degree
  • Shanks Centered on Tires
  • Walking Tandems in All Locations
  • 11L x 15-12 Ply, 12.5L x 15-12 Ply, 12.5L x 15 Load Range F (Model Dependent)
  • Single Point Depth Control
  • Blue Powder Coat Paint
  • Safety Warning Lights

Photos

Highlights

  • Albany, Georgia
  • 2023
  • Landoll
  • 9600 Series Field Cultivator 9630-20
  • Available

Specifications

  • 2023
  • Landoll
  • 9600 Series Field Cultivator
  • 9630-20
  • Cultivator
  • Requirements: 7 to 9 HP (5 to 7 kW) Per Foot
  • Main Frame: (4) 280/70Rx15 Radial Tires | Wing Frame: (4) 280/70Rx15 Radial Tires
  • Hubs - Main Frame: 6-Bolt | Hubs - Wing Frame: 6-Bolt
  • Self-Leveling Hitch | Category: Cat. III Ball Hitch
  • Truss Type with Wrapped Shank Tube Joints
  • Shank Size: 0.625in. x 1.75 in. (15.9 x 44.5 mm) On Edge | Spring Size: 0.46875 in. (11.9 mm) Wire Diameter | Shank Spacing: 6 in. (152 mm), Split the Middle Pattern | Spacing Between: Shank Rows 30 in. (762 mm) Minimum | Sweeps: 8 in. (203 mm) with 47 Degree Mount | Under Frame Clearance: 26.5 in. (673 mm) | Frame: 3 in. x 4 in. x 0.25 in. (76.2 x 102 x 6.4 mm) | Transport Lift Axles: 4.5 in. (114 mm) Axle with Tower Lift System | Hydraulics: 10 in. (254 mm) Stroke Cylinders
  • 16 ft. 0 in. (4.9 m)
  • 9 ft. 3 in. (2.8 m)
  • 20 ft. 6 in. (6.2 m)
  • Main Frame: 2.25 in. (57.2 mm) Slip-In Spindles | Wing Frame: 2.25 in. (57.2 mm) Slip-In Spindles
  • Fore-to-Aft: 135 in. (3.4 m)
  • Point: 190 lbs. (86 kg)
  • Approximate - Spring Shanks: 9,600 lbs. (3,130 kg) | Approximate - S-Tine Shanks: 8,985 lbs. (4,076 kg)
  • Number of Shanks: 41 | Number of Shanks per Section: 9-23-9 | Spring Shank Tower: Laser Cut/Matchcut Components | Spring Shank Pivots: Nitrotec Coated Inter-Locking Clamp Bushing | Shank Position: Rear Shanks Centered on Tires | Walking Tandems: Standard with Maintenance Free Pivot Bushings | Machine Depth Control: Single Point, Front Mounted
  • Spring Clamp Shanks or 2-Piece S-Tine Shanks
  • Frame: Laser Cut/Matchcut Components, Robotically Welded