2024 John Deere Draper Platform RDF45

2024 John Deere Draper Platform RDF45

Swipe to View More

  • Year 2024
  • Make John Deere
  • Model Draper Platform
2024 John Deere Draper Platform RDF45

2024 John Deere Draper Platform RDF45

2024 John Deere Draper Platform RDF45

  • Harvest crops as close as possible to the ground with the HydraFlex™ cutterbar
  • Minimize grain loss with a two-speed center feed section
  • Enable higher harvesting speed without sacrificing cut quality with a 4” double cut, dual drive, shaft driven cutterbar
  • Get more done by eliminating header calibrations

Features may include:

Optimize feeding with a two-speed center feed section, increased feed drum torque, and center crop flow divider

OVERVIEW

Increase grain in the tank with a two-speed center feed section. A slow-speed setting softens the impact of crop fingers and drum flighting when engaging with crop. This ensures that easy-shelling crops like lentils and soybeans do not get thrown over the feeder house. Use the high-speed setting in canola or high-yielding cereals to prevent slug feeding while ensuring that the drum does not plug.

BENEFITS
  • Experience less downtime during harvest related to unplugging the header, which allows for more harvesting time at the highest productivity levels.
  • Higher feed drum torque is matched to the capacity of the combine to ensure optimal feed rates into the combine. Higher torque on the front feed drum allows operators to confidently harvest tough feeding crops like canola.
  • Additionally, prevent underfeeding in light crops with the center crop flow divider. When not harvesting crop with the full width of the draper, the center crop flow divider prevents crop from skipping over the center feed section and going on the opposite draper belt.
ADDITIONAL DETAILS
  • The two-speed center feed section maintains a consistent ratio between the feed drum and center feed belt speed.
  • Change center feed section speed with a toolless, two-speed, easy-shift handle on the gearcase to the left of the draper feeder house opening.

Superior ground following with the HydraFlex™ draper system

OVERVIEW

Achieve superior ground following when harvesting in a wide range of terrains, crops, and conditions with RDF HydraFlex Draper Platforms. HydraFlex is an industry-exclusive hydraulic float system.

BENEFITS
  • Float closely to the ground over changing conditions by controlling the cutterbar ground pressure from the cab – simply adjust the armrest knob to vary hydraulic pressure in the float arm hydraulic cylinders.
ADDITIONAL DETAILS
  • The hydraulic float system features a 7.5-in. (19-cm) float range.
  • To lock out the HydraFlex draper into rigid mode, the operator should increase the float pressure to maximum

Evenly feed canola and field peas into the feeder house with RDF top augers

BENEFITS
  • With the crop tucked under the auger, the handoff to the center feed drum enables smooth and consistent feeding to the combine to ensure constant load.
  • Achieve smooth headfirst feeding when auger speeds are running slightly faster than the belt speed.
ADDITIONAL DETAILS
  • It is recommended for operation in bushy or high-volume harvesting conditions such as canola.
  • Augers can be turned off for crops like lentils or wheat where they are not recommended.

Operational

Operating Speed Knife: X Series Combine: 520 cycles/min / S-Series Combine: 490 cycles/min | Pickup reel operating: 6-70 rpm | Low speed: 200 rpm / High speed: 240 rpm | Draper belts - Operating: Side belts (variable): 1-3.5 m/s (3.3-11.5 fps) / Center belts: 211 m/min (692 fpm) / Low-speed center belt (fixed): 4.2 m/s (13.8 fps) / High-speed center belt (fixed): 5.1 m/s (16.7 fps)

Dimensions

Dimensions Knife drive - Double-cut, dual-drive, shaft-driven cutterbar: 4 in. (10.2 cm) | Pickup reel - Diameter: 42 in. (106.7 cm) | Cutterbar vertical flex: 7.5 in. (190 mm) | Reel lift: 28.3 in. (72 cm) | Reel fore and aft: 14.1 in. (35.9 cm) | Fore of the cutterbar: 16 in. (40.6 cm) | Feed drum - Diameter: 16.3 in. (414 mm) | Feed drum fingers - Heavy-duty and round with breakaway notch and retainer Diameter: 0.625 in. (16 mm) | Finger reach: 6 in. (152 mm)
Cutterbar Length 45 ft (13.72 m)
Length 50.1 ft (15.3 m) | Platform: 47.9 ft (14.6 m)
Height Base skid shoe: 1.5 in. (3.8 cm) | Cleat: 0.75 in. (19.05 mm)
Width Side belts: 40 in. (101.6 cm) / Center belts: 70 in. (177.6 cm)
Transport Width field position: 47.9 ft (14.6 m)
Depth, Maximum Belt: 39.8 in. (101.2 cm) | Overall operating - With dividers: 9 ft (2.74 m)
Auger Diameter Top - Size: 18 in. (45.7 cm)

Weights

Weight Approximate: 9782 lb (4437 kg)

Features

Features Draper belts speed control: Hydraulic from cab (side belts only) | Platform Type: Hinged frame rigid cutterbar | Pickup reel - General Two-piece, poly tine pickup reel with 8-in. (20-cm) tube | Number of slats: Six bat poly | Height control: Hydraulic | Speed control: Hydraulic | Number of fingers: 21 | Auger finger platform: Triple chevron, retracting | Header height sensing: Electrohydraulic
Cutterbar Type Straight-line knife drive system
Construction Material Fingers: Nylon

Product Photography