2020 Rhino Equipment Wheel Loaders RWL132
- Year 2020
- Make Rhino Equipment
- Model Wheel Loaders
- Engine Model: 6BTA5
2020 Rhino Equipment Wheel Loaders RWL132
Rhino® Wheel Loaders are today’s solution to meet high performance requirments, have maximum uptime, and low cost operation. Designed to keep you competitive, these loaders let you finish the job faster and put more profit in your pocket.
The RWL series allows you to work hard and efficiently in all conditions. Repeatable fine modulation gives superior bucket control with less spillage. RWL Series electro-hydraulic implement controls and load-sensing hydraulic system with simultaneous lift and tilt capabilities offer better control with less effort.
Rhino® wheel loaders saves you money by keeping operating costs to a minimum – getting more work done per unit of fuel used.
Features may include:
- If you`ve got maximum productivity in mind, the RWL Series Loaders should be at the top of your list. But it`s not just their big torque reserves thet make them such impressive performers. Joystick control provide smooth, near-effortless control. Rhino® hydraulics sense the load and deliver the flow needed for smooth combined functions and fast work cycles.
- Control panel provides access to critical machine info, brake and throttle pedals are conveniently positioned for maximum comfort to the operator.
- Rhino® cylinders offer superior strength and dent resistance deliver longer component life and reduced risk of system contamination. Rhino® Cylinders and Rods are designed to allow for a variety of service / repair options.
- High quality hose products mean fewer hose changes. Rhino® Equipment offers a broad line of high, medium and low-pressure hoses and couplings that are engineered and tested far beyond industry standards for top performance and long life.
Engine
Engine Manufacturer
Cummins | Rhino®
Engine
Model: 6BTA5
Emissions
Tier2
Cylinder Liners
6
Displacement
5.9 L (360 cu. In)
Engine Power
Net Power kW (Hp) @ Rated rpm: 126(169)@ 2,200 rpm
Engine Torque
Net Peak Torque Nm (lb-ft) @ Rated rpm: 643(474)@ 1,600 rpm
Lubrication
Full-flow spin-on filter
Aspiration
Turbocharged, charge air cooled
Air Cleaner
Under-hood, dual element dry type, restriction indicator on filter housing for service
Fuel System
Fuel System
Direct Injection
Drivetrain
Final Drive
Heavy duty inboard-mounted planetary
Transmission
Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
Differential Lock
Helical bevel gear
Steering
Type: Articulated frame, fully hydraulic | Articulation Angle: 35 degrees | Raise sec.: 6.2 | Dump sec.: 3.8 | Lower sec. : 1.8 | Total sec.: 11.8
Battery
Battery
2-12 volt: 120A
Electric
Electrical
24 Volts
Alternator
70 Amp
Brakes
Rear braking system
Rear Axel Oscillation (with 20 R 25 tires): 22 degrees (11 degrees each direction)
Brake System Type
Service: Pneumatically assisted, hydraulically actuaded, four wheels disk brake
Parking Brake
Manually activated, drum mounted on front output shaft
Wheels & Tires
Tires, Front Specification
20.5 R 25 16 Ply: (Tread Width 2,050 mm (80.7 in) | Width Over Tires: 2,570 mm (101.2in) )
Tires, Rear Specification
20.5 R 25 16 Ply: (Tread Width 2,050 mm (80.7 in) | Width Over Tires: 2,570 mm (101.2in) )
Operational
Operating Speed
Maximum Travel Speeds (with 16 R 24 tires) 1st Gear: 10 km/h (6 mph) | Maximum Travel Speeds (with 16 R 24 tires) 1st Gear: 12 km/h (7 mph) | Maximum Travel Speeds (with 16 R 24 tires) 2nd Gear: 36 km/h (22 mph)
Cycle Time
Hydraulic: Z-Bar
Operating Conditions
Breakout Force: 13,400 Kg (29,542 lb) | Max. Rollback at Ground Level: 49 degrees | Max. Rollback, Boom Fully Raised: 57 degrees | Max. Bucket Dump Angle, Fully Raised: 45 degrees
Hydraulics
Hydraulic Pump
Pump (Loader and Steering): Gear Pump, variable displacement, closed-center
Hydraulic Flow
Max. Rated Flow at 2,200 rpm L/min (gpm): 115(30)
Maximum Pressure
System Relief Pressure (Loader and Steering): 17 Mpa (2,466 psi)
Dimensions
Dimensions
Reach, 45 degree Dump, 2,130mm (7ft) Clearance: 1,485 mm (4.9 ft) | Loader Clearance Circle, Bucket Carry Position: 11,995 mm (39.4 ft)
Turning Radius
Steering (measured to centerline of outside tire): 5,730 mm (18.8 ft)
Height
Top of Cab and Canopy: 3,430 mm (11.3 ft) | Hood: 3,310 mm (9.9 ft) | Hinge Pin, Fully Raised: 3,832 mm (12.6 ft) | Dump Clearance, 45 degree Full Height: 2,815 mm (9.2 ft) | Reach, 45 degree Dump, Full Height: 1,050 mm (3.4 ft)
Ground Clearance
400 mm (1.3 ft)
Wheelbase
3,080 mm (10.1 ft)
Overall Length
Bucket on Ground: 7,248 mm (23.8 ft)
Depth, Maximum
Max. Digging Depth: 190 mm (0.6 ft)
Width
Bucket: 2,685 mm (8.8 ft)
Capacities
Fuel Capacity
Tank: 200 L (53 gal)
Cooling System
17 L (4 gal)
Oil capacity
Engine: 13.5 L (4 gal)
Transmission Fluid Volume
45 L (12 gal)
Axle Capacity, Rear
Axle Oil (Front and Rear, each): 20 L (5 gal)
Hydraulic Capacity
Tank: 150 L (40 gal)
Features
Brake System (Front and Rear Booster Pump, each): 1.5 L (0.4 gal)
Heaped Capacity
2.3 m3 (3.0 cu. Yd)
Struck Level
2.0 m3 (2.6 cu. Yd)
Cargo Capacity
Tipping Load, Straight: 10,255 Kg (22,608 lb) | Tipping Load, 35 degree Full Turn: 8,990 Kg (19,820 lb)
Weights
Weight
Bucket: 960 Kg (2,116 lb)
Weight, In Running Order
Operating: 13,200 Kg (29,101 lb)
Features
Features
Fan Drive: Belt driven | Loader Controls: Dual-multiway valve, joystick control