2020 Rhino Equipment Wheel Loaders RWL65

2020 Rhino Equipment Wheel Loaders RWL65

Swipe to View More

  • Year 2020
  • Make Rhino Equipment
  • Model Wheel Loaders
  • Engine Model: 4BT3
2020 Rhino Equipment Wheel Loaders RWL65

2020 Rhino Equipment Wheel Loaders RWL65

2020 Rhino Equipment Wheel Loaders RWL65

Rhino® Wheel Loaders are today’s solution to meet high performance requirments, have maximum uptime, and low cost operation. Designed to keep you competitive, these loaders let you finish the job faster and put more profit in your pocket.

The RWL series allows you to work hard and efficiently in all conditions. Repeatable fine modulation gives superior bucket control with less spillage. RWL Series electro-hydraulic implement controls and load-sensing hydraulic system with simultaneous lift and tilt capabilities offer better control with less effort.

Rhino® wheel loaders saves you money by keeping operating costs to a minimum – getting more work done per unit of fuel used.

Features may include:

  • If you`ve got maximum productivity in mind, the RWL Series Loaders should be at the top of your list. But it`s not just their big torque reserves thet make them such impressive performers. Joystick control provide smooth, near-effortless control. Rhino® hydraulics sense the load and deliver the flow needed for smooth combined functions and fast work cycles.
  • Control panel provides access to critical machine info, brake and throttle pedals are conveniently positioned for maximum comfort to the operator.
  • Rhino® cylinders offer superior strength and dent resistance deliver longer component life and reduced risk of system contamination. Rhino® Cylinders and Rods are designed to allow for a variety of service / repair options.
  • High quality hose products mean fewer hose changes. Rhino® Equipment offers a broad line of high, medium and low-pressure hoses and couplings that are engineered and tested far beyond industry standards for top performance and long life.

Engine

Engine Manufacturer Cummins | Rhino®
Engine Model: 4BT3
Emissions Tier2
Cylinder Liners 4
Displacement 3.3 L (201 cu. In)
Engine Power Net Power kW (Hp) @ Rated rpm: 60(80)@2,200 rpm
Engine Torque Net Peak Torque Nm (lb-ft) @ Rated rpm: 259(191)@2,200 rpm
Lubrication Full-flow spin-on filter
Aspiration Turbocharged
Air Cleaner Under-hood, dual element dry type, restriction indicator on filter housing for service

Fuel System

Fuel System Direct Injection

Drivetrain

Transmission Type: Powershift | Torque Converter: Single-stage, Dual-phase, Quad-element torque | Operator Interface: Steering column lever for two gears forward and one in reverse | Shift Modes: Manual activation (Forward: 1st and 2nd; Reverse: 1st)
Differential Lock Helical bevel gear
Steering Type: Articulated frame, fully hydraulic | Articulation Angle: 38 degrees | Raise sec.: 5.0 | Dump sec.: 2.0 | Lower sec. : 3.2 | Total sec.: 10.2

Battery

Battery 2-12 volt: 120A

Electric

Electrical 24 Volts
Alternator 70 Amp

Brakes

Rear braking system Rear Axel Oscillation (with 16 R 24 tires): 22 degrees (11 degrees each direction)
Brake System Type Service: Pneumatically assisted, hydraulically actuaded, four wheels disk brake
Parking Brake Manually activated, drum mounted on front output shaft

Wheels & Tires

Tires, Front Specification 16 R 24 10 Ply: (Tread Width 1,600 mm (63.0 in) | Width Over Tires: 2,010 mm (79.1 in) )
Tires, Rear Specification 16 R 24 10 Ply: (Tread Width 1,600 mm (63.0 in) | Width Over Tires: 2,010 mm (79.1 in) )
Tire Pressure, Front 0.3 Mpa (4.3 psi)
Tire Pressure, Rear 0.3 Mpa (4.3 psi)

Operational

Operating Speed Maximum Travel Speeds (with 16 R 24 tires) 1st Gear: 6 km/h (4 mph) | Maximum Travel Speeds (with 16 R 24 tires) 1st Gear: 6 km/h (4 mph) | Maximum Travel Speeds (with 16 R 24 tires) 2nd Gear: 24 km/h (15 mph)
Cycle Time Hydraulic: Z-Bar
Operating Conditions Breakout Force: 5,700 Kg (12,566 lb) | Max. Rollback at Ground Level: 49 degrees | Max. Rollback, Boom Fully Raised: 55 degrees | Max. Bucket Dump Angle, Fully Raised: 45 degrees

Hydraulics

Maximum Pressure System Relief Pressure (Loader and Steering): 16 Mpa (2,321 psi)
Hydraulic Pump Pump (Loader and Steering): Gear Pump, variable displacement, closed-center
Hydraulic Flow Max. Rated Flow at 2,200 rpm L/min (gpm): 100(26)

Dimensions

Dimensions Reach, 45 degree Dump, 2,130mm (7ft) Clearance: 1,355 mm (4.4 ft) | Loader Clearance Circle, Bucket Carry Position: 10,525 mm (34.5 ft)
Turning Radius Steering (measured to centerline of outside tire): 4,420 mm (14.5 ft)
Height Top of Cab and Canopy: 2,975 mm (9.8 ft) | Hood: 2,810 mm (9.2 ft) | Hinge Pin, Fully Raised: 3,465 mm (11.4 ft) | Dump Clearance, 45 degree Full Height: 2,520 mm (8.3 ft) | Reach, 45 degree Dump, Full Height: 960 mm (3.1 ft)
Ground Clearance 342 mm (1.1 ft)
Wheelbase 2,300 mm (7.5 ft)
Overall Length Bucket on Ground: 5,710 mm (18.7 ft)
Depth, Maximum Max. Digging Depth: 146 mm (0.5 ft)
Width Bucket: 2,070 mm (6.8 ft)

Capacities

Fuel Capacity Tank: 110 L (29 gal)
Oil capacity Engine: 16 L (4 gal)
Transmission Fluid Volume 20 L (5 gal)
Axle Capacity, Rear Axle Oil (Front and Rear, each): 13 L (3 gal)
Hydraulic Capacity Tank: 100 L (26 gal)
Features Brake System (Front and Rear Booster Pump, each): 1.5 L (0.4 gal)
Heaped Capacity 1.0 m3 (1.3 cu. Yd)
Struck Level 0.75 m3 (1.0 cu. Yd)
Cargo Capacity Tipping Load, Straight: 6,452 Kg (14,224 lb) | Tipping Load, 35 degree Full Turn: 5,560 Kg (12,258 lb)

Weights

Weight Bucket: 542 Kg (1,195 lb)
Weight, In Running Order Operating: 6,550 Kg (14,440 lb)

Features

Features Fan Drive: Belt driven | Loader Controls: Dual-multiway valve, joystick control

Product Photography